Loctite® Frekote 770-Nc Chemical Auxiliary for Polyester Resins

• Customization: Available
• CAS No.: 1174921-67-5
• Appearance: Liquid
• Model NO.: LOCTITE FREKOTE770-NC
• Usage: Oil Drilling Auxiliary Agent, Water Treatment Chemicals, Rubber Auxiliary Agents, Plastic Auxiliary Agents, Coating Auxiliary Agents, Textile Auxiliary Agents, Paper Chemicals, Surfactants, Leather Auxiliary Agents, Electronics Chemicals
• Color: Clear, Colorless
• Cure: Room Temperature Cure
• Cured Thermal Stability: ≤400 °c
• Application: Release Coatings
• Application Temperature: 15 to 60 °c
• Density: 0.72 g/cm3
• Transport Package: Wooden Box
• Specification: Solvent Based Polymer
• Trademark: Evergreen
• Origin: Jiangsu, China
• HS Code: 3815900000
• Production Capacity: 10 Tons/Month

Product Description

LOCTITE® FREKOTE 770-NC

Product Description

PRODUCT DESCRIPTION

LOCTITE® FREKOTE 770-NC™ offers excellent release for

various molding applications. LOCTITE® FREKOTE 770-NC™

can be used for the release of epoxies, polyester resins, vinyl

ester resins, thermoplastics, adhesives, and rotationally molded

plastics. This product is particulary well suited for tougher to

release processes such as filament winding and non gel coated

polyester and fiberglass molding.
 

TYPICAL PROPERTIES OF UNCURED MATERIAL

Specific Gravity @ 25 °C                          0.715 to 0.725

 

GENERAL INFORMATION

This product is not recommended for use in pure oxygen and/or

oxygen rich systems and should not be selected as a sealant

for chlorine or other strong oxidizing materials.

Storage

The product is classified as flammable and must be stored in

an appropriate manner in compliance with relevant regulations.

Do not store near oxidizing agents or combustible materials.

Store product in the unopened container in a dry location.

Storage information may also be indicated on the product

container labelling.

 

Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or

greater than 28 °C can adversely affect product properties.

Material removed from containers may be contaminated during

use. Do not return product to the original container. Henkel

cannot assume responsibility for product which has been

contaminated or stored under conditions other than those

previously indicated. If additional information is required,please

contact your local Technical Service Center or Customer

Service Representive.

Conversions

(°C x 1.8) + 32 = °F                kV/mm x 25.4 = V/mil

mm / 25.4 = inches                 µm / 25.4 = mil

N x 0.225 = lb                         N/mm x 5.71 = lb/in

N/mm² x 145 = psi                  MPa x 145 = psi
N·m x 8.851 = lb·in                 N·m x 0.738 = lb·ft

N·mm x 0.142 = oz·in             mPa·s = cP
 

Note:(1)

The information provided in this Technical Data Sheet (TDS) including the recommendations for use and application of the

product are based on our knowledge and experience of the product as at the date of this TDS. The product can have a

variety of different applications as well as differing application and working conditions in your environment that are beyond our control.

Note:(2)

Henkel is,therefore, not liable for the suitability of our product for the production processes and conditions in respect

of which you use them, as well as the intended applications and

results. We strongly recommend that you carry out your own

prior trials to confirm such suitability of our product.

Any liability in respect of the information in the Technical Data Sheet or any other written or oral recommendation(s) regarding

the concerned product is excluded,except if otherwise explicitly agreed and except in relation to death or personal injury caused by our negligence and any liability under any applicable

mandatory product liability law.

 

Product Parameters

 

PRODUCT DESCRIPTION
Technology	Mold Release	Appearance	Clear, Colorless
Chemical Type	Solvent Based Polymer	Odor	Mild, Solvent
Cure	Room temperature cure	Cured Thermal Stability	≤400ºC
Application	Release Coatings	Application Temperature	15 to 60ºC
Specific Benefit	No contaminating transfer	High gloss finish	High slip
	No mold build-up	Low odor
Physical and chemical properties
Physical state:	liquid	Evaporation rate:	Not available
pH:	Not available.Product is non polar/aprotic.	Melting point:	Not determined
Boiling point:	> 112ºC(> 233.6ºF)	Density:	0.72 g/cm3
Vapor density:	3.9Approximately, (Air = 1)	Vapor pressure:	Not available.
Flash point:	7 °C (44.6 °F)	Ignition temperature:	> 284 °C (> 543.2 °F)

Application

Our Advantages

Why Choose Us?

1.Provide Full Export Certificates Necessary For Export In Short Time, Delivery Time Fast .

2.No District Limit , Can Export Our Chemicals To Every Corner Of The World.

3.Corporate With World Famous Brand, Quality Assured, Cost Effective .

4.Professional And Strong Technical Support.

5.Full Line Nouryon Brand Peroxides

6.Hot Chemicals, Short Of Supply Chemicals, We Have .

7.Rich Export Experience In High Dangerous Goods , Like Chemicals Trigonox 301,Perkadox 16 Which Need Cool Container.
 

Production Process

Company Profile

Evergreen Chemicals is a leading manufacturer and supplier of chemical composite materials in China. We've been and kept leading roles in this industry for more than 20 years, serving 8000+ customers all over the world from more than 25 fields. Our company is located in Jiangyin, half an hour to Shanghai by train, enjoying convenient transportation access.

We are specialized in researching, producing and distributing resin materials and its auxiliaries with premium quality. Our main products are unsaturated polyester resin, epoxy resin, vinyl resin and organic peroxides. In addition to market our own products, we are also the distributor of some global brands like NUORYON, SWANCOR, AOC, INOES etc.  

Besides, auxiliaries like curing agent, accelerator, and initiator are also available here to customers. Our products are widely used in the fields of automobiles, tent poles, cooling towers, pipes, FRP, artificial stones, handicrafts, and resin manhole covers.

Certifications

 

FAQ

1. Q: Is your company a manufacturer?
     A: Yes,we are. At the same time, we are also agents of other product brands.

2. Q:  Does your company provide samples?
     A:  Yes,we  can provide 100g and 200g for additive and 500g/1kg for resin as free samples,  but freight usually requires the buyer to bear.

3. Q:What is your company's  transportation form?
     A: Samples generally deliver by international express, a large number of goods can be transported by land or water.

4: Q: What is the quality and price of your product?
     A: Specializing in epoxy resin and other unsaturated polyester resin .100% tested and working before shipment .best price will grant you as per your quantity .

5. Q: How many days the clear phenolic epoxy resin could sotre ?
    A: 12 months below 25ºC in dark.